Elements to Consider on BGA Assembly Process Capability


Reading time ( words)

BGA (ball grid array) assembly is totally compatible with soldering assembly technology. Chip-scale BGAs can have pitches of 0.5 mm, 0.65 mm or 0.8 mm, while plastic or ceramic BGA components feature wider pitches like 1.5 mm, 1.27 mm and 1 mm.

Fine-pitch BGA packages are more easily damaged than integrated circuits (ICs) with pin packages, and BGA components allow selective reduction of contact points to meet the specific requirement on I/O pins. As a cutting-edge technology applied in SMT assembly, BGA packages have quickly become a significant selection to conform to fine pitch and ultrafine pitch technology, achieving high-density interconnection with a reliable assembly technology provided, which leads to the increasingly more applications of this type of package.

Application of X-Ray Tomography in BGA Assembly

Most PCB manufacturers and electronics manufacturers haven’t noticed too much necessity to apply X-ray inspection in their manufacturing process until BGA components are applied in electronics assembly. Traditional inspection methods were regarded to be sufficient, such as manual visual inspection and electrical test, including manufacturing defect analysis (MDA), in-circuit test (ICT) and function test.

However, all those inspection methods fail to find out hidden solder joint issues such as cavities, cold soldering, and bad tin-soldering adhesion. X-ray inspection system is a type of inspection tool that has been verified to be capable of inspecting hidden solder joints and help establishing and controlling manufacturing process, analyzing prototype and confirming process. Different from MDA, ICT and AOI, an X-ray inspection system is capable of confirming short circuits, open circuits, cavities and BGA solder ball alignment, monitoring process quality and providing instant feedback data for statistical process control (SPC) with high manufacturing efficiency.

X-ray tomography inspection devices can generate tomography images through capturing images of solder joints that are able to implement automatic solder joint analysis and real-time tomography scanning. Moreover, they can carry out accurate comparison analysis on all solder joints of components on both sides of a PCB board within a couple of seconds or two minutes, leading to a conclusion whether solder joints are qualified or not.

BGA Assembly Process and Variation Source

To use X-ray inspection system more effectively, control parameters of BGA assembly process and parameter control limitations have to be clarified. BGA assembly process conforms to the sequence in Figure 1.

When BGA components’ eutectic solder balls are assembled in solder paste during assembly process, their positions are usually corrected through self-alignment of liquid soldering tin. Thus, mounting precision seems not so essential as fine-pitch lead components and the leading control phase in BGA component assembly technology is solder paste printing and reflow soldering. In addition, variation in terms of solder joint shape and size is also associated with many other elements.

It’s almost impossible to eliminate all the variations, so the key point in manufacturing process control is to reduce variation in each manufacturing phase. The influence of different variations on final assembly products should be carefully analyzed and quantitatively processed. With the whole process from BGA components to PCB assembly process considered, leading elements affecting solder joint quality are:

  • Volume of solder balls
  • BGA component pad size
  • PCB pad size
  • Solder paste volume
  • BGA component deformation during reflow soldering process
  • PCB deformation at BGA mounting area during reflow soldering process
  • Mounting placement accuracy
  • Reflow soldering temperature curve

No matter what type of inspection device is used, there must be a basis when judging whether solder joints are qualified or not. IPC-A-610C regulates the definition of acceptance criteria of BGA solder joints in 12.2.12 item. Excellent BGA solder joints are required to be smooth, round, clear in edge and with no cavities. Diameter, volume, grayscale and contrast should be the same for all solder joints with position aligned and no displacement or twist.

To read the full version of this article, which appeared in the May 2018 issue of SMT007 Magazine, click here.

Share


Suggested Items

Tips to Improve Soldering Tip Life and Reduce Cost

10/10/2018 | Thermaltronics
Whether in production, or repair and rework, the cost of soldering iron tips can be easily overlooked, but with today’s requirement for higher temperatures in lead-free solder applications, the consumption of tips has dramatically increased. This fact, combined with changes in tip design to meet the higher thermal load requirements, has also resulted in escalating tip costs, making tip care a high priority.

What SMT Component Shortages Mean for Design and Manufacturing Engineers

09/13/2018 | Russell Poppe, JJS Manufacturing
Much has been written about the increasing shortages of electronic components such as MLCCs, chip resistors and other semiconductor devices. And the manufacturing industry is now seeing price increases and greatly extended lead times. It seems the situation is likely to get rapidly worse rather than better. What can we do? Read on.

RTW NEPCON South China: Mycronic Discusses Industry 4.0

09/12/2018 | Real Time With... NEPCON South China
At the recent NEPCON South China 2018 event in Shenzhen, Clemens Jargon, VP for Global Dispensing and Asia at Mycronic, discusses I-Connect007's Edy Yu the challenges that customers face on their journey towards Industry 4.0, and how Mycronic is addressing these issues. From jet printing to solder paste inspection, to pick-and-place, Jargon talks about their total solutions that aim to help customers take their production to the next level.



Copyright © 2018 I-Connect007. All rights reserved.