PCB Pad Repair Techniques


Reading time ( words)

There are a variety of reasons behind pads getting "lifted" completely or partially from the laminate of a PCB. Per the just revised IPC-A-610 Revision G, a defect for all three classes occurs when the land is lifted up one or more pad thicknesses. Lifted pads can occur when a device has been improperly removed or there is a manufacturing defect in the board construction. The propensity for this to occur when pads are very small, like in the case of an 0201 or when there is an unconnected BGA pad.

In any case, as with any repair, the ultimate decision on the ability to repair the pad lies with the customer. In some cases, only a limited number of repairs are allowed by the customer and if allowed the same repairs can only be attempted with customer-approved materials and methods. Like all repairs defined by the IPC 7711/21 Rework of Electronic Assemblies/Repair and Modification of Printed Boards and Electronic Assemblies, the repairs can only be done with customer approval.

Wettermann-Fig1-8Jan18.jpg

Figure 1: Initial damaged pad requiring replacement.

There are two different industry-accepted repair techniques for lifted pads when the objective is to replace the pad. One involves the use of dry film heat and pressure curable adhesive that is stuck to the replacement pad. The second involves the use of a two-part epoxy and “gluing” the replacement pad to the laminate. While the better method usually involves personal preferences, pull test data and better observed results of the replacement pad staying in position post soldering makes the epoxy method the one of choice.

The epoxy repair technique outlined in IPC-7721 Rev C Procedure 4.7.1, describes a method for the repair of pads by using a replacement plated pad (attached via a skeleton of other patterns) and a two-part epoxy adhesive system. Each of the steps in the process require cleaning for best possible adherence of the repair materials as well as well as for inspection to make sure that the procedure is done properly. To start, remove the pad with a sharp knife and carefully cut a small piece of the connecting circuit.

Wettermann-Fig2-8Jan18.jpgFigure 2: Replacement pads of commercial circuit frame.

Using the proper solder and flux, attach the replacement pad with the connecting circuit by lap soldering the two together. Mix the two-part epoxy per the manufacturer’s suggestions, direct the mixture and apply pressure to the replacement pad and laminate and cure per the manufacturer’s instructions. (This technique also works for still attached but lifted only pads.) Make sure to inspect for anomalies and perform an electrical continuity test as a post repair check.

In a second repair method (IPC 7721 Procedure 4.7.2), a dry film-backed plated replacement pad is adhered to the PCB laminate by a heat and pressure-activated dry film. All the process steps in the above epoxy method apply until you get to the sequence where a repair material is chosen. Once the replacement pad in the circuit frame is identified, it is cut out from the frame using a sharp blade. Only in this case the technician has to make sure that they cut through both the replacement pad as well as the adhesive backing. Now the pad is soldered to the trace if required.

Wettermann-Fig3-8Jan18.jpgFigure 3: Replacement pad held down with Kapton tape for epoxy/resin curing process.

A special tip and handheld heating tool similar to a soldering iron is placed into a fixture which controls the downward pressure. Through this heated tip temperature and tip pressure the adhesive cures. The other steps are similar in nature to the epoxy repair method.

One of the most challenging types of pad repair are those with embedded vias. These vias, connected to other board layers, will still need to maintain their connectivity to the connected layer post repair. There are numerous approaches to maintaining these very difficult repairs including but not limited to small jumper wires of small copper trace interconnections.

There are two methods for repairing damaged pads. Both the two-part epoxy/resin and the dry film techniques will do the job. In either event, a highly-skilled and trained technician can make most of these types of repairs when financially viable and where the risks of reliability have been mitigated based on the end use operating environment.

Reference

1. IPC 7711/21 Rework of Electronic Assemblies/Repair and Modification of Printed Boards and Electronic Assemblies.

Share


Suggested Items

Investigation on the Assembly Process for m03015 and a Brief Look at m0201 Components

11/14/2018 | David Geiger, Robert Pennings, and Jane Feng, Flex
Components continue to shrink in the SMT world, and the next evolution of passive components includes m03015 (009005) and m0201 (008004). The m03015 and the m0201 components will see primary adoption in products that require further miniaturization, which would be SiPs. These modules would then be assembled into products through attachment, another assembly, or via other interconnect methods. This article explores the development of an assembly process (SMT only) for the m03015 component.

How to Avoid Common Wave Soldering Issues

11/13/2018 | Neil Blundell, Blundell Production Equipment
Wave soldering involves using waves of molten solder that act as glue to attach electrical components to the PCB. While this process is expedient and efficient in producing high-quality products, it sometimes experiences glitches that can be prevented or corrected. This article explores some of the main issues and how to remedy them.

Alpha Assembly Solutions on Training, Education, and Low-Temperature Soldering

11/07/2018 | I-Connect007 Editorial Team
In this interview, Jason Fullerton of Alpha Assembly Solutions discusses the benefits and challenges of low-temperature soldering. He also highlights the biggest concerns he’s currently seeing in the industry, including young engineers lacking hands-on manufacturing experience and training, voiding and head-in-pillow issues, and low-temperature soldering demands.



Copyright © 2018 I-Connect007. All rights reserved.