Laserssel Brings High-speed Soldering to New Application Areas


Reading time ( words)

Barry Matties spoke with Denis Barbini, general manager of Laserssel, about the Korean company’s new laser-selective reflow solution aimed at reducing a typical reflow oven’s 10-minute cycle down to just 10 seconds as well as the overall benefits manufacturers could see from streamlining this process.

Barry Matties: Denis, can you tell us a little bit about Laserssel?

Denis Barbini: We are a soldering company focused on using laser technology in a novel way. We started in 2015 performing research and development for this revolutionary technique. We investigated the potential for integration into electronics assembly, and that’s why we are serving the semiconductor, SMT, and rework markets today.

Matties: This is a specialty process. Is the idea that the machine streamlines the hand soldering process?

Barbini: We’re addressing current customer problems with mass soldering, mass convection of reflow of soldering, and wave soldering. We’re taking common defects, such as warpage for a fine-pitch assembly where it is increasingly challenging to achieve proper coalescence, and optimizing those processes to eliminate the warpage to get excellent yield and reliability. We’re also able to process niche applications like flex-on-flex and flex-on-rigid in an automated, in-line process rather than having to utilize hand soldering.

We are identifying industry segments and applications to automate processes where assemblers have had problems over the last few years. The industry is undergoing an explosion of applications, such as new components and designs for IoT and wearables. This requires different ways of soldering. You can’t just use a reflow oven or a wave soldering machine. This technique is very conducive to providing a solution to the current and future assembly challenges.

Matties: In terms of streamlining the process, what are some of the measurable benefits that people will get?

Barbini: Some benefits include improved quality of the soldering joint, reliability of the product, increased units per hour (UPH), and minimized defects with a lower cost of operation in terms of electricity and no inert atmosphere required compared to typical forced convection ovens. When I look at the work that we’ve done, it’s primarily flex-on-flex and automotive batteries, semiconductor devices with pitches of less than 40 microns and die thickness less than 100 microns, and SMT assembly of temperature-sensitive components. While the industry is identifying the potential for low-temperature solders to address specific assembly challenges, this technique mitigates or even eliminates those challenges with SAC alloys. We are enabling them to get that into a mass production environment so that they don’t have to worry about using all of the techniques that are slower and a little bit more cumbersome.

Matties: How long has this equipment been in the marketplace?

Barbini: For the past two and a half years.

Matties: How many installs do you have currently?

Barbini: Now, we have around 40 machines worldwide.

Matties: What has the feedback been?

Barbini: It’s always too good to be true. When we look at semiconductor, their cycle of integrating new technology takes a couple of years. We started with them three years ago, and last week, we installed a new machine at a semiconductor fabrication house where they are now soldering their products in mass volume. We are very excited about that, but it takes time to integrate new technology into the marketplace because we’re comparing joints that were formed by reflow soldering, which everyone knows really well. Today, we are enabling a paradigm shift using our area laser. We can still get high UPH and as good or better quality than reflow.

Matties: This is suitable for what volume of their work? Is 100% of their work running through this, or is it very selective and somewhat niche?

Barbini: Right now, Laserssel is targeting specific applications. However, we see that depending on the application itself, we can potentially solder an entire board in less time than a reflow process. While there is a way to solder the entire product, we’re not out there to replace reflow soldering; we are here to provide customers with solutions to their current challenges and enable them to solder new types of applications that they never thought they could do before.

Matties: What are the general questions that people have about this technology?

Barbini: The first question is usually, “Is my joint quality that’s being formed going to be better or worse?” Because everyone’s used to a certain microstructure, intermetallics, and coalescence. Moreover, we’re taking a process that takes six minutes for reflow and turning it into less than 10 seconds. The next question is, “Are we getting the same dynamics?” about the physical operations taking place in reflow compared to our machine, which is why we’ve taken the time to conduct a two-year study to do just that.

Matties: Do their customers care that it’s going through this process versus a reflow?

Barbini: Initially, the questions come up, so yes, they do.

Matties: How do you satisfy those questions?

Barbini: We’re doing evaluations. Currently, we have two demo centers in the U.S. and one in South Korea. We’re doing a lot of evaluations to prove to the customer that we can do it in an automated fashion with quality.

Matties: Going back to what you just said earlier, it’s typically a 10-minute cycle versus 10 seconds.

Barbini: We’re using the AREA laser. Traditional spot lasers aim at a spot where it applies all of the energy and solders one lead at a time. That’s visible, right? But we’re not doing that. We’re taking that energy and distributing that over an area. It could be 80 by 80 mm or as small as 600 by 300 microns, and the uniform density of energy will solder all of those components equally in that area. By doing that, if you’re giving an 80 by 80 mm, there are a handful of applications that are much smaller than that—such as sensors or automotive or medical applications—so we can process that very quickly.

To read the full article, which appeared in the June 2019 issue of SMT007 Magazine, click here.

Share

Print


Suggested Items

Comparing Soldering Results of ENIG and EPIG Post-steam Exposure

09/11/2019 | Jon Bengston and Richard DePoto, Uyemura International USA
Electroless nickel immersion gold (ENIG) is now a well-regarded finish used to enhance and preserve the solderability of copper circuits. Electroless palladium immersion gold (EPIG), meanwhile, is a new surface finish also for enhancing and preserving solderability—but with the advantage of eliminating electroless nickel from the deposit layer. This feature has become increasingly important with the increasing use of high-frequency PCB designs whereby nickel’s magnetic properties are detrimental.

Solder Mask Evolves into a Truly Additive Process

09/09/2019 | John Fix, Taiyo America Inc.
The 5G era is creating quite a bit of work for many PCB engineers as the materials required to keep up with the speed, frequency, and latency requirements need to be defined and qualified. Solder mask, for example, now becomes a truly additive process. Read on to find out how and why.

Selecting the Proper Flex Coverlayer Material

09/06/2019 | Dave Lackey, American Standard Circuits
Coverlayers are polymer materials used to cover and protect the copper traces of the flex circuit product. There are a number of different options available for protecting the circuits, and they serve different design requirements in terms of cost, performance, and flexural endurance optimization. When specifying the choice, it is critical to call out not just the type of coverlayer material but also the thickness requirement. This can be very important in certain types of constructions, especially when a flex circuit will experience dynamic flexing during use.



Copyright © 2019 I-Connect007. All rights reserved.